将窗口固定在显示器上_如何建立可夹在任何办公桌上的显示器固定架

本文主要是介绍将窗口固定在显示器上_如何建立可夹在任何办公桌上的显示器固定架，希望对大家解决编程问题提供一定的参考价值，需要的开发者们随着小编来一起学习吧！

将窗口固定在显示器上

If you need to raise your monitor higher than what the stock stand can achieve, a monitor mount or arm is a great way to do that. Here’s how to build your own.

如果您需要将显示器抬高到架子无法达到的水平，则可以使用显示器固定架或支臂来达到此目的。这是构建自己的方法。

You can get monitor mounts and arms for pretty cheap, but if you’re not a huge fan of the selection or just want something really simple and customizable, you can build your own monitor mount that can clamp onto almost any desk surface. Plus, it takes less than 30 minutes to make.

您可以以相当便宜的价格获得显示器支架和支架，但如果您不是选择的忠实拥护者，或者只是想要真正简单且可定制的东西，则可以构建自己的显示器支架，以将其固定在几乎任何桌面上。另外，制作时间不到30分钟。

你需要什么 (What You’ll Need)

You’ll only need a few tools to get the job done, as well as a handful of materials. I used:

您只需要几个工具就可以完成工作，以及少量材料。我用了：

A power drill with drill bits
带钻头的电钻
A pencil
铅笔
A 12-inch threaded galvanized steel pipe (You can get any length you want—this will determine how high your monitor sits)
12英寸镀锌螺纹钢管(您可以根据需要选择任何长度，这将决定显示器的高度)
3-inch threaded galvanized steel pipe (Again, you can get any length, but it’s only needed to attach the VESA mount)
3英寸镀锌螺纹钢管(同样，您可以获得任何长度，但只需要连接VESA支架即可)
An elbow joint
肘关节
A flange fitting
法兰配件
A couple of small C-clamps
几个小型C型夹
Small wood screws (Four of them ideally, but extras are good to have)
小号木螺钉(理想情况下为四个，但最好有其他螺钉)
A scrap piece of cheap wood
一小块便宜的木头
A VESA monitor mount plate (Any plate will work, but you’ll likely have to think of your own creative way to mount it to the pipe).
VESA显示器安装板(任何板都可以使用，但是您可能必须考虑自己的创造性方式才能将其安装到管道上)。

Make sure that all of your pipes and fittings are the same size throughout. So if you get 3/4-inch pipe, you’ll need 3/4-inch fittings as well. The size is up to you, though.

确保所有管道和配件的尺寸相同。因此，如果您有3/4英寸的管道，则也需要3/4英寸的配件。不过，大小取决于您。

第一步：将管道法兰拧到废木上 (Step One: Screw the Pipe Flange to the Scrap Wood)

The first thing we’ll do is attach the pipe flange to our scrap piece of wood, which will make up the base of the monitor stand. To start, we need to mark on the piece of wood where the screws will be drilled in order to attach the flange. Set the flange on the piece of wood and mark where the holes are with your pencil.

我们要做的第一件事是将管道法兰连接到我们的废木片上，这将构成显示器支架的底座。首先，我们需要在要钻出螺钉的木板上做标记，以固定法兰。将法兰盘放在木头上，并用铅笔标记Kong的位置。

You’ll end up with four circles where we’ll need to drill pilot holes.

您将与四圈，我们会在需要钻结束了导向Kong。

Take your power drill and a drill bit and drill four small holes where marked. You don’t need to drill all the way through the wood, but there’s no reason not to if you’re in a hurry, since you won’t see the bottom anyway.

拿起电钻和钻头，在标记的地方钻四个小Kong。您无需一直在木材上钻Kong，但是也没有理由不着急，因为您还是看不到底部。

Next, grab a screwdriver or change out the drill bit for the drive bit and screw the flange to the wood using four small wood screws. Make sure the screws aren’t long enough that they’ll pierce through the other side.

接下来，用一把螺丝起子或将钻头换成驱动钻头，然后用四个小木螺钉将法兰固定到木上。确保螺钉的长度不足以刺穿另一侧。

第二步：连接主支撑钢管和弯头接头 (Step Two: Attach the Main Support Steel Pipe and Elbow Joint)

After you have the base all ready to go, it’s time to erect the main support pipe that will sit vertically. Since the end is threaded, all you have to do is screw it into the flange and tighten it down the best you can.

准备好所有底座之后，该竖立主支撑管了。由于端部是带螺纹的，因此您所要做的就是将其拧入法兰，并尽最大可能将其拧紧。

This pipe will also determine how high or low your monitor sits relative to the desk surface. So the longer the pipe is, the higher your monitor will sit. I went with a 12-inch length since that’s a good sweet spot.

该管道还将确定显示器相对于桌面的高度。因此，管道越长，显示器的坐姿就越高。我走了12英寸长，因为那是一个不错的选择。

After that, you can screw on the elbow joint. I ended up having to get a T-fitting since the hardware store was out of 3/4-inch elbow joints, but it still gives me the 90-degree angle that I need.

之后，您可以拧紧肘关节。由于硬件商店没有3/4英寸的肘关节，我最终不得不获得T形接头，但是它仍然给了我所需的90度角。

第三步：将VESA安装板固定到管道上 (Step Three: Attach the VESA Mount Plate to the Pipe)

Take your short length of pipe and determine how you’ll attach the VESA mount plate to it. This will take a bit of creativity on your part, but here’s is how I did mine. I first needed to drill a hole completely through the pipe in order to stick a bolt through to attach my VESA mount.

拿短长度的管道，然后确定如何将VESA安装板固定到其上。您将需要一点点创造力，但这就是我的工作方式。首先，我需要在管道上完全钻一个Kong，以插入螺栓以固定我的VESA支架。

To do this, place the pipe into a bench vise for stability.

为此，将管道放入台钳中以保持稳定性。

Next, take a drill bit meant for drilling into metal and go to town, making sure to apply a lot of pressure but going slowly. If done right, you should end up with some clean holes on either side of the pipe.

接下来，钻一个用于钻进金属的钻头，然后进城，确保施加很大的压力，但要缓慢。如果操作正确，您应该在管道的两边都留下一些干净的Kong。

Screw the pipe into the elbow joint on the monitor mount, making sure that it’s as tight as possible, but also making sure that the holes are facing up and down.

将管道拧入显示器底座的弯头，确保尽可能紧，但还要确保Kong朝上和朝下。

Next, grab the VESA mount and slide it over the pipe, lining up the holes as you do so. From there, take the bolt and slide it through, securing the other end with a nut.

接下来，抓住VESA支架并将其在管道上滑动，同时将Kong对齐。从那里，取下螺栓并滑入，用螺母固定另一端。

The stand is now complete and ready to be transported to the nearest desk.

架子现已完成，可以运输到最近的桌子。

第四步：将显示器安装架固定在办公桌上 (Step Four: Clamp the Monitor Mount to Your Desk)

Find a place where you want your monitor stand and make sure it will work where it is.

找到您想要显示器站立的地方，并确保它可以在原处工作。

From there, take your two C-clamps and clamp the monitor mount to your desk, using the wood as the clamping point. Ideally you’ll want to face the clamps down, so that the bulk of the clamp isn’t showing and you have a cleaner look.

从那里开始，拿起两个C型夹，然后将木头固定在显示器上，将显示器固定到桌面上。理想情况下，您将要使夹具朝下，这样就不会显示夹具的大部分，而且您的外观也更干净。

第五步：将显示器连接到显示器支架 (Step Five: Attach the Monitor to the Monitor Mount)

Take your VESA mount plate and screw it onto the back of the monitor. It’s also a good idea to remove the stock stand on the monitor, since you won’t need it.

拿下VESA固定板并将其拧到显示器背面。删除显示器上的架子也是个好主意，因为您将不需要它。

Lastly, carefully attach the monitor to your DIY mount. For my monitor, the VESA mount plate hooks onto the section that I bolted onto the pipe.

最后，小心地将显示器连接到您的DIY支架上。对于我的显示器，VESA安装板钩在我用螺栓固定到管道上的部分上。

Once your monitor is mounted, it may take some adjustments to get it level and placed exactly where you want, but other than that, your monitor mount is all ready to go!

安装好显示器后，可能需要进行一些调整才能使其水平并准确放置在所需的位置，但是除此之外，您还可以准备好显示器安装架！

Again, feel free to customize this any way you want in order to mount your monitor in the best place possible for your setup. You may want yours mounted higher than mine, so go ahead and use a longer pipe if necessary. Or if you just need to raise it up another inch or so, take another block of wood and stack it below the base.

同样，请随意以任何方式自定义此选项，以便将显示器安装在最适合安装的位置。您可能希望将其安装在比我的更高的位置，因此，如有必要，请使用更长的管道。或者，如果您只需要将其抬高另一英寸左右，则拿另一块木头并将其堆叠在底座下方。