本文主要是介绍vmware 安装gentoo注意的事项，希望对大家解决编程问题提供一定的参考价值，需要的开发者们随着小编来一起学习吧！
参考：http://gentoo-wiki.com/HOWTO_Install_Gentoo_on_VMware_4_in_Windows_NT/2K/XP
第一关：虚拟机的网卡
mware有三种模式：
桥接模式：把虚拟机当成一个真正主机，端口全部对外开放。
NAT模式：与host共享网卡上网，如果要ssh必须在vmware 的nat tab中进行端口映射。
host－only模式：与主机完全分离的模式。
最简单最好用的就是nat模式了，如果不把虚拟机当成服务器使用，建议使用NAT模式。
把ssh端口22 映射出来。
第二关：内核配置
配置内核首先要对自己的机器硬件环境非常熟悉，只有配置好了驱动才能正常的使用机子。
可以使用lspci和lsmod，查看检测到的设备以及livecd加载的所有模块。这样才配置内核时可以参考配置。
VMWare Tools
VMware Tools uses Kernel Loadable Module support to load and unload its driver(s).
| Linux Kernel Configuration: kernel loadable module support |
Loadable module support ---> [*] Enable loadable module support [*] Module unloading [*] Automatic kernel module loading |
Intel PCI/ISA Bridge
| Linux Kernel Configuration: Intel PCI/ISA Bridge |
Bus options (PCI etc.) ---> [*] PCI Support [*] ISA Support |
SCSI Controller
LSI Logic
Linux Kernel Configuration: LSI Logic SCSI adapter Device Drivers --->
Fusion MPT device support --->
<*> Fusion MPT (base + ScsiHost) drivers
OR
<*> Fusion MPT ScsiHost drivers for SPI [kernel 2.6.13]
Device Drivers --->
SCSI device support --->
<*> SCSI device support
<*> SCSI disk support
SCSI low-level drivers --->
<*> SYM53C8XX Version 2 SCSI support
BusLogic
Device Drivers ---> Fusion MPT device support ---> <*> Fusion MPT (base + ScsiHost) drivers OR <*> Fusion MPT ScsiHost drivers for SPI [kernel 2.6.13]
Device Drivers ---> SCSI device support ---> <*> SCSI device support <*> SCSI disk support SCSI low-level drivers ---> <*> SYM53C8XX Version 2 SCSI support
By default, VMware virtual machines provide a BusLogic SCSI controller and a SCSI hard drive. Your new kernel should have these device drivers for them:
| Linux Kernel Configuration: BusLogic SCSI |
Device Drivers ---> SCSI device support ---> <*> SCSI device support <*> SCSI disk support SCSI low-level drivers ---> <*> BusLogic SCSI support |
CDROM
| Linux Kernel Configuration: Intel PIIXn chipset and ISO9660 File System |
Device Drivers ---> ATA/ATAPI/MFM/RLL support ---> <*> Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support <*> Include IDE/ATAPI CDROM support [*] PCI IDE chipset support [*] Generic PCI bus-master DMA support <*> Intel PIIXn chipsets support File systems ---> CD-ROM/DVD Filesystems ---> <*> ISO 9660 CDROM file system support [*] Microsoft Joliet CDROM extensions |
Network
You will need to enable the following to get basic packet and TCP/IP support.
| Linux Kernel Configuration: Network |
Networking ---> [*] Networking support Networking options ---> <*> Packet socket <*> Unix domain sockets [*] TCP/IP networking |
PCnet-PCI II
Linux Kernel Configuration: Network Device Drivers --->
Network Device support --->
[*] Network device support
Ethernet (10 or 100Mbit) --->
[*] Ethernet (10 or 100Mbit)
[*] EISA, VLB, PCI and on board controllers
<*> AMD PCnet32 PCI support
Device Drivers ---> Network Device support ---> [*] Network device support Ethernet (10 or 100Mbit) ---> [*] Ethernet (10 or 100Mbit) [*] EISA, VLB, PCI and on board controllers <*> AMD PCnet32 PCI support
Audio
| Linux Kernel Configuration: Sound |
Device Drivers ---> Sound ---> <*> Sound card support Advanced Linux Sound Architecture ---> <*> Advanced Linux Sound Architecture <*> OSS Mixer API <*> OSS PCM (digital audio) API PCI devices ---> <*> (Creative) Ensoniq AudioPCI 1371/1373 |
udev Support
| Linux Kernel Configuration: Miscellaneous Things |
File Systems ---> Pseudo filesystems ---> <*> /proc file system support < > /proc/kcore support <*> Sysctl support (/proc/sys) <*> sysfs file system support <*> Virtual memory file system support (former shm fs) |
第三关：安装gnome
按照官方文档，安装gnome的时候出现循环依赖。解决办法是：
USE="-qt3 -qt4 -arts -kde X dbus gtk gnome hal avahi" 去掉最后边的avahi。
关于每个use标示的意义可以在/usr/portage/profiles/use.desc中查看。
还有就是use中最好去掉-doc 很容易导致循环依赖。
这篇关于vmware 安装gentoo注意的事项的文章就介绍到这儿，希望我们推荐的文章对编程师们有所帮助！
